Coiling machine not only has the precision mechanical components, also equipped with a powerful electric control system, it sets the electrical control, sensing technology, mechanical transmission, pneumatic device parts, such as the debug method compared with other electric processing equipment more complex and subtle. The mechanical strength of rotor parts under centrifugal force and bearing mechanical strength when speeding, under the condition of the high strength and full load test the quality of the automatic winding machine.

變壓器繞線機:http://freshscreen.cn

Transformer winding machine

常見的帶骨架線圈的纏繞加工工藝，主要講解起繞位置、漆包線規格、繞線寬度三個重要的繞線參數。

Common skeleton coil winding process, the covers up around the place, enameled wire specification, winding process width of three important parameters.

一、 起繞位置如何設定

A, how to set up around the position

簡單的說就是在骨架上開始繞線的起點，這個位置與線圈的出頭及線圈類型有緊密的聯系，通?？梢酝ㄟ^設備控制系統自帶的測量功能來測的相關起繞位置的具體數值；操作人員也可以采用人工方式測量，以固定點作為參考點使用尺具實際測量，設定該點時注意線圈的纏繞方向。

Simple said is the starting point of start winding on the skeleton, the position and the coil head and coil type are closely linked, usually by equipment control system comes to the features of the measuring test of related position around the specific number; Operators can also be measured by artificial means, in fixed point used as a reference point feet with actual measurement, set the point attention to coil winding direction.

二、漆包線規格的設定

Second, the setting of enameled wire specifications

我們常見的漆包線有不同的線徑，漆包線規格設定是否正確直接會影響到排線的效果，使用不同材質的漆包線需要加不同的線徑修正值，銅線不易被拉細，其修正值加0.02左右,鋁線在經過繞線設備的張力及過線裝置后容易被拉伸,其修正值幅度較大0.02-0.2之間都是允許的。

Our common have different wire enameled wire, enameled wire specifications set correctly will directly affect the effect of row line, using different materials of the enameled wire need to add different wire diameter revised, copper wire is not easy to be fine, the revised of around 0.02, aluminium wire tension during the winding equipment and easy to stretch after line device, and the revised larger extent between 0.02 to 0.2 are allowed.

三、繞線寬度的設定

Third, set the width of winding

繞線寬度的理解就是從開始繞線的位置到繞線結束位置之間的距離，通常該值直接反映骨架需要繞線的長度，變壓器繞線機設定時需要考慮所使用骨架的微小變形量對繞線寬度的影響，應采用綜合測量的方法取最小值作為繞線寬度。

The understanding of the winding width is from start winding process to the position of the distance between the end position, usually the value directly reflects the skeleton need the length of the winding, transformer winding machine need to be considered when setting used tiny deformation will influence of the width of the winding frame, should adopt comprehensive measurement method takes the minimum as the winding width.